View previous topic :: View next topic |
Author |
Message |
ram
![](images/avatars/3016781794d671460f209e.jpg)
Joined: 01 Mar 2010 Posts: 46 Location: Cochrane Alberta
|
Posted: Wed Mar 24, 2010 5:06 pm Post subject: AT 309 Stock Impeller VS SS Inpeller Whats the Difference? |
|
|
I recently Purchased a new 20 foot Outlaw Clearwater with a 330 HP 350 and a AT 309 and I upgraded to the SS impeller I Talked to alot of people who said I should and I was wondering if anyone could tell me what are the real benifits to the SS impeller, I am new to the jet boat world and I plan on using the boat in Northern rivers for Huntung as well as a family rec boat, Thanks for your Time. Anyone know where the closest open water is to Cochrane I am dying to get my boat in the water for the first Time ![Cool](images/smiles/icon_cool.gif) |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Will R
Joined: 31 Jul 2005 Posts: 677 Location: NWT/Alberta
|
Posted: Wed Mar 24, 2010 5:22 pm Post subject: |
|
|
congrats on the new boat you'll love it!as for reason...very simple sht 'n' abuse and peace of mind. a cast aluminum impeller isnt even conparable really to a ss one unless you plan on using it as a deep water boat only. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Boomhower
![](images/avatars/114663859359bc4b76a5e2a.jpg)
Joined: 03 Nov 2007 Posts: 995
|
Posted: Wed Mar 24, 2010 9:31 pm Post subject: |
|
|
Well said Will, Hey Ram, in a good afternoon of boating you can chew up an aluminum impeller, Especially if your a ROOKIE.
Its a good piece of Mind knowing you have a good blade in your pump.
A definate must for any Riverboat. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
thundercat
Joined: 22 Apr 2008 Posts: 10 Location: Edmonton / Chip Lake
|
Posted: Wed Mar 24, 2010 10:40 pm Post subject: |
|
|
Put in under the bridge at Cochrane Mar 16, 2010. Ran up to the first island for lunch then up to the dam. Went because it was winter and forecast 19c. _________________ THUNDERCAT |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
JetstreamConcepts
Joined: 29 Sep 2009 Posts: 8
|
Posted: Thu Mar 25, 2010 11:19 am Post subject: 309 ss verse alumium |
|
|
the only thing you need to be aware of is that you will need to put RTV on the main drive spline , unbolt the motor slide it forward and put RTV on the spline slide motor back and let it set up overnight this will stop that banging sound coming from the jet at idle |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Hines
![](images/avatars/127783758543d5b98232954.png)
Joined: 05 Jul 2005 Posts: 304 Location: Red Deer
|
Posted: Thu Mar 25, 2010 12:06 pm Post subject: |
|
|
SS is great life its steal , Boom how do you chew up a alum. imp. in a day of boating are you near the river?LoL.Later. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Rapid Transit
Joined: 20 Jun 2005 Posts: 206
|
Posted: Thu Mar 25, 2010 2:34 pm Post subject: |
|
|
what is RTV ?[/quote] |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
rustyzipper
Joined: 08 Oct 2009 Posts: 67
|
Posted: Thu Mar 25, 2010 3:48 pm Post subject: |
|
|
One type of single-product silicone sealant is called Room Temperature Vulcanizing (RTV). This form of sealant starts to cure as soon as it is exposed to the air.
Dont use to much though. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
big block
![](images/avatars/12807712624bd4d0d8f093f.jpg)
Joined: 09 Jun 2008 Posts: 102 Location: calgary
|
Posted: Thu Mar 25, 2010 5:11 pm Post subject: Re: 309 ss verse alumium |
|
|
JetstreamConcepts wrote: | the only thing you need to be aware of is that you will need to put RTV on the main drive spline , unbolt the motor slide it forward and put RTV on the spline slide motor back and let it set up overnight this will stop that banging sound coming from the jet at idle |
lets see i had this problem then after my splines got really worn and a bad vibration i took it apart and have found that there was not enough spline overlap, there 2.5 to 3 inch usable spline there and was only about maybe 1 inch at best overlap so now im going to find another yoke and re fit the driveline to use as much spline on the pump posible. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Doogie
Joined: 31 Jan 2010 Posts: 4
|
Posted: Fri Mar 26, 2010 3:51 am Post subject: Re: 309 ss verse alumium |
|
|
JetstreamConcepts wrote: | the only thing you need to be aware of is that you will need to put RTV on the main drive spline , unbolt the motor slide it forward and put RTV on the spline slide motor back and let it set up overnight this will stop that banging sound coming from the jet at idle |
Your answer seem a little out of place considering the original question...
But the RTV is a good Trick if you are trying to scam someone into buying an old worn out boat. The proper fix is a new yoke and Impeller shaft as Big Block Said.
And to reduce the Harmonic pulses at idle you should be running a FLYWHEEL not a Flexplate.
The Flexplate running without a torque converter bolted to it has less support for the starter ring
Which allows the plate to flex more than its original design and possibly develop cracks. A broken flexplate is no fun.
The mass of the FLYWHEEL supports the Ring gear Properly and Eliminates the
"banging sound coming from the jet at idle" |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Itsworthit
![](images/avatars/19837816654bbe57b5ebded.jpg)
Joined: 15 Jun 2005 Posts: 432 Location: Whitecourt
|
Posted: Fri Mar 26, 2010 5:22 pm Post subject: |
|
|
Doogie..................where have you been all these years, we have so many questions to ask you, can you explain how the ring gear not being supported by a flywheel makes the loud bang when the jet is at idle |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
mountainman
Joined: 15 Jan 2006 Posts: 131 Location: Grande Prairie, Alberta
|
Posted: Fri Mar 26, 2010 8:15 pm Post subject: |
|
|
Itsworthit wrote: | Doogie..................where have you been all these years, we have so many questions to ask you, can you explain how the ring gear not being supported by a flywheel makes the loud bang when the jet is at idle |
Because the starter isn't disengaging come on now ![Rolling Eyes](images/smiles/icon_rolleyes.gif) |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Will R
Joined: 31 Jul 2005 Posts: 677 Location: NWT/Alberta
|
Posted: Fri Mar 26, 2010 8:23 pm Post subject: |
|
|
ever clever eh! ![Laughing](images/smiles/icon_lol.gif) |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Viking502
![](images/avatars/140635524147cdb774e8b54.gif)
Joined: 23 Nov 2007 Posts: 137 Location: Alberta Beach, AB
|
Posted: Sat Mar 27, 2010 1:46 pm Post subject: |
|
|
Itsworthit wrote: | Doogie..................where have you been all these years, we have so many questions to ask you, can you explain how the ring gear not being supported by a flywheel makes the loud bang when the jet is at idle |
ALSO DOGGY:
Could you pwees hep me wit sumpin'...
Why is it whin i put me fingger in the ewectrical socket my hair stands on end. The wast time I was out wurking on the RIGS (I work for free because I already have too much money) da guys had me do dat.
Day aslo said dat if I went an got dem dar pipe stwetchers they would not waff at me anymor.
PS.
PWEES HELP.
U my onwy hope!!! _________________ The GENE POLICE told me to "Get out of the pool". |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
mountainman
Joined: 15 Jan 2006 Posts: 131 Location: Grande Prairie, Alberta
|
Posted: Sat Mar 27, 2010 1:49 pm Post subject: |
|
|
Ohh and please direct me to the closest store for a couple cans of compression I have been searching high and low for it, my oscillating foo-foo valve seems to be disjointed. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|