OUTLAW EAGLE MANUFACTURING Forum Index OUTLAW EAGLE MANUFACTURING
ALUMINUM BOAT FORUM
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Another impeller question

 
Post new topic   Reply to topic    OUTLAW EAGLE MANUFACTURING Forum Index -> OE GENERAL FORUM
View previous topic :: View next topic  
Author Message
Gent911



Joined: 16 Apr 2011
Posts: 29
Location: Montreal Quebec

PostPosted: Mon Jun 10, 2013 4:02 pm    Post subject: Another impeller question Reply with quote

here are my numbers
im turning an A2 ss impeller at 5400-5500
im at 630bs torque@4500 and 643hp@6000
what do I want to do turn lower or higher?



IMG_0573.JPG
 Description:
 Filesize:  149.15 KB
 Viewed:  10831 Time(s)

IMG_0573.JPG


Back to top
View user's profile Send private message Yahoo Messenger MSN Messenger
Will R



Joined: 31 Jul 2005
Posts: 677
Location: NWT/Alberta

PostPosted: Mon Jun 10, 2013 4:47 pm    Post subject: Reply with quote

I'd say stay where it's at. Really decent power and torque numbers there! Start spinning it higher and you may start running into problems. Just my two cents bud!
_________________
When in doubt hammer down!
Back to top
View user's profile Send private message
Gent911



Joined: 16 Apr 2011
Posts: 29
Location: Montreal Quebec

PostPosted: Mon Jun 10, 2013 6:16 pm    Post subject: Reply with quote

I have a 9.5" aluminum impeller that I can try on and cut down to play with, will a aluminum impeller pump the same water a ss one would?

I mean size for size will the end result be the same
Back to top
View user's profile Send private message Yahoo Messenger MSN Messenger
boosted



Joined: 04 Jun 2009
Posts: 378

PostPosted: Tue Jun 11, 2013 7:57 am    Post subject: Reply with quote

No the s.s steel ones usually pull about 200 rpm less on the same cut. is it an AT impeller. You could go to a Agressor as the A2 is a little more aggressive than the a/t one. They also have what they call an econo cut which is like an A3.5. You wouls prob pull that at about 5000.
_________________
Mark

Lets go back I think we missed one rock!
Back to top
View user's profile Send private message
Gent911



Joined: 16 Apr 2011
Posts: 29
Location: Montreal Quebec

PostPosted: Tue Jun 18, 2013 11:00 am    Post subject: Reply with quote

they are both A/T the 9.5 inches is aluminum and never tried it on, the one that is on right now is AA Stainless and makes me turn 5400
my top end is only 70 right now. I would like to get a detailed stainless Hi-helix but don't really want to spend that much before knowing what will give me better top end that's why I wanted to try the aluminum one and turn it down from where it is until no gain is obtained. that's if there is more to start with
Back to top
View user's profile Send private message Yahoo Messenger MSN Messenger
Display posts from previous:   
Post new topic   Reply to topic    OUTLAW EAGLE MANUFACTURING Forum Index -> OE GENERAL FORUM All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group :: Spelling by SpellingCow.