| View previous topic :: View next topic |
| Author |
Message |
didehcho
Joined: 04 Oct 2011
Posts: 34
Location: yellowknife
|
 Posted: Thu Oct 06, 2011 11:12 am Post subject: first jet boat and looking for spec on hull and maintenace |
 |
|
Well just got my first used jet boat 2001 1800 eagle marine
looking for spec on the hull and a manual for the 175 sj and pump
it got a steel plate on the bottom
There two small flat head srews just forward of the grate, is that for the gear box and what type of oil should be used. Is the same principle as to fill the an out board leg with gear oil
| Description: |
|
| Filesize: |
258.28 KB |
| Viewed: |
15601 Time(s) |
|
|
|
| Back to top |
|
 |
JET1
Joined: 03 Jun 2010
Posts: 42
|
|
| Back to top |
|
|
didehcho
Joined: 04 Oct 2011
Posts: 34
Location: yellowknife
|
| Posted: Fri Oct 07, 2011 10:44 am Post subject: |
|
|
| Right on thanks Where should I send the beer too!
|
|
| Back to top |
|
|
buffalo bill
Joined: 26 Jan 2011
Posts: 15
Location: red deer
|
| Posted: Fri Oct 07, 2011 1:30 pm Post subject: |
|
|
I dont know where he's from but feel free to send it to outlaw and well forward it to him
_________________
hey can you help me get this couch in my van |
|
| Back to top |
|
|
Boomhower
Joined: 03 Nov 2007
Posts: 995
|
| Posted: Fri Oct 07, 2011 3:01 pm Post subject: |
|
|
| Yeah, one of the scews is the overflow and one the drain. ReFill it from the drain and when it starts to come out the over flow its full. Then quickly get the plug back in. Mercury hi performance gear oil is what you want.
|
|
| Back to top |
|
|
didehcho
Joined: 04 Oct 2011
Posts: 34
Location: yellowknife
|
| Posted: Fri Oct 07, 2011 8:51 pm Post subject: |
|
|
yup for sure ill drop a flat when I am down south next summer. Been going to Sylvan lake every year and always admire them hulls in the yard.
Yup figured out the screws and had some water in it. Now I am getting ready for a load of moose meat.
|
|
| Back to top |
|
|
didehcho
Joined: 04 Oct 2011
Posts: 34
Location: yellowknife
|
| Posted: Fri Oct 07, 2011 8:54 pm Post subject: |
|
|
| boomher would you know what the spec on this hull its a 2001 from sylvan
|
|
| Back to top |
|
|
didehcho
Joined: 04 Oct 2011
Posts: 34
Location: yellowknife
|
| Posted: Fri Oct 07, 2011 8:56 pm Post subject: |
|
|
| boomhower
|
|
| Back to top |
|
|
rokchucker
Joined: 15 Sep 2009
Posts: 36
Location: Ft Assiniboine AB
|
| Posted: Mon Oct 17, 2011 2:37 pm Post subject: |
|
|
if there was water in the case,you might wanna check your output shaft seal before ya go too far into the wild.water in gearboxes is usually pretty bad news,as it can cause damage to bearings.cheers
_________________
if ya cant hit bottom ,beat the hell outta the sides |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
